v0.31:Water wheel

xTATTEREDx  · +FINE+  · *SUPERIOR*  · ≡EXCEPTIONAL≡  · ☼MASTERWORK☼

Water wheel

b-M-w
═ ═ ═ X X X
Construction
Materials	Jobs
3 Template:L	Template:L Template:L
Power
Needs 10 power. Generates 100 power. Net gain of 90 power.

v50.14 · v0.47 · v0.34 · v0.31.25 · v0.28 · v0.23 This article is about an older version of DF. More Info · V

A water wheel is a Template:L that provides Template:L via water Template:L. To build a water wheel, select build menu and choose Machine components. It requires 3 Template:L and generates 90 net power, which can be used for operating one or more Template:L or Template:Ls. You can use Template:Ls and Template:L to distribute the power produced by a water wheel, or connect the machinery directly.

Waterwheels do not work with waterfalls, nor in magma - it takes water that is flowing according to the DF use of the term.

For a basic overview of how the different machine parts work and work together, see Template:L.

Construction

The Template:L and Template:L labors are needed for the construction.

A water wheel occupies 3 adjacent tiles (N-S or E-W axis, no diagonals). It is the color of the first wood selected for it, so you could build a red wheel with one piece of goblin-cap and two of fungiwood.

Although it's possible to build a stable water wheel on solid ground, it won't provide any power. A useful water wheel is built in an empty tile that does not contain a floor, allowing the wheel to be powered by water in the tiles one Template:L below. Floorless tiles are typically made by Template:Lling away the floor. To support the water wheel, build it with its central tile orthogonally adjacent to a gear assembly, a horizontal axle, a screw pump, or the central tile of a pre-existing water wheel. Do not hang it from a gear assembly you wish to control with a switch, as a disconnected ("switched off") gear assembly can't support anything and will cause the waterwheel to deconstruct.

Template:L is generated from a water wheel as long as it has Template:Ling water at a depth of 4/7 or greater under at least one of its tiles. The easiest way to achieve this is by placing the water wheel over a Template:L or Template:L. With a brook you must first channel through the surface since brooks have a floor of sorts over them.

Designs

Key:
  
  #    = Wall
  ○    = Millstone
  +    = Floor
  ~    = Water  
  W    = Water Wheel
  *    = Gear Assembly  
  ═    = Axle

Basic watermill design

#	+	+	+	+	~	+
#	+	+	+	+	~	+
#	○	+	+	+	W	+
#	*	═	═	═	W	+
#	+	+	+	+	W	+
#	+	+	+	+	~	+
#	+	+	+	+	~	+

Dual watermill design

#	+	+	+	+	~	~
#	+	+	+	+	~	~
#	○	+	+	+	W	W
#	*	═	═	═	W	W
#	+	+	+	+	W	W
#	+	+	+	+	~	~
#	+	+	+	+	~	~

This is by no means the limit of water power from one location, depending on the width of your river/brook/channel you can stack many waterwheels side-by-side (really big assembles will need to be artificial as there's a limit to how wide the game created water flows get). Just remember to make sure there's a support structure in place before you place the next wheel.

Perpetual motion

Due to the relatively low power draw of a Template:L, a self-powering assembly can be made with a water wheel that still leaves plenty of excess power for other uses. This is arguably an Template:L (violating basic principles of physics), and possibly a bug.

To get it working, you must start the pump manually.*

(* Exceptions are Template:Ls, which can sometimes have naturally occurring Template:L. This is sometimes a good thing, because then a wheel simply works by itself - or a bad thing, if, for example, you want the wheel to not provide any power while you build a pump adjacent to it. It's not clear what causes an aquifer to have flow and then keep it - it's difficult to replicate reliably, and can be lost with additional Template:Ling, so designs will have to be adapted if such are found.)

It is good to have a ready source of water to refill the machine, as water tends to escape and evaporate. As the water level decreases, the water wheel may intermittently stop providing power; when the level falls below 4/7, the wheel stops providing power altogether.

*REMEMBER TO BUILD AN ORTHOGONAL PUMP, HORIZONTAL AXLE OR GEAR ASSEMBLY BEFORE THE WATER WHEEL*

Dwarven Water Reactor

Key

║ ═ ╝ ╚ ╔ ╗ ╣ ╠ ╩ ╦ O = Wall

+ = Floor

W = Water Wheel with floor underneath

W = Water Wheel with water underneath

≈ = Water on current level

≈ = Water on level below

X
X = Screw Pump drawing from south

This compact design, once started, produces 170 surplus power (less additional power train). While the water reactor provides a perpetual source of mechanical power in abundant amounts, the use of several reactors can cause performance issues. When building your water reactor, it is recommended that you include a method for stopping the reactor once started.

Lower Level		Upper Level
╔ ═ ╦ ═ ╗ ║ ≈ ║ ≈ ║ ║ ≈ ║ ≈ ║ ║ ≈ O ≈ ║ ╚ ╗ ≈ ╔ ╝ █ ╚ ═ ╝ █		╔ ═ ═ ═ ╗ ║ W + W ║ ╝ W X W ╚ + W X W + + + ≈ + + + + + + +

Dig the V-shaped channel and fill it with water (either from an outside source or by designating it as a Template:L). Meanwhile, construct the pump, pumping from the South. Construct the two water wheels. Start the pump manually ( q, Enter ) - if there is enough water*, the "reactor" will start immediately and the pump operator will leave. The water from the north end of the pump will spill over the top-most floor tile, filling that to 7/7 and the two tiles east and west of it to ~5/7, but will not overflow back past the water wheel to the walkway area. Note that for the upper level, no southern walls are shown as none are needed, unless you don't follow the design and do something to create water pressure.

• (* Estimated minimum depth to prime the reactor is 3/7 to 4/7, though this is not guaranteed.)
• The ideal amount of water in this design is apparently 63 units of water. In other words six tiles below in the V are full up to 7/7 and three more above are also full up to 7/7 which will generate reliable flow permanently without ever losing any of that water to evaporation. An easy way to do this is to simply leave your pond fill command on after the reactor activates. They will eventually fill it up to the optimal level and stop.

The reactor can be safely halted either by blocking the tile the pump draws water from or "overloading" the reactor (since drawing more power than the reactor supplies will stop the pump that keeps the cycle going until the load is reduced and the pump is manually restarted by dwarf-power), More drastically, the reactor will obviously be halted by deconstructing the pump. Deconstructing one wheel will cause a flood (and almost immediately cancel any job order to deconstruct the other components), and deconstructing the pump will cause both wheels to collapse (unless they are attached to Template:L outside them, not shown).

Template:L can routed up from the pump or off to the side from a wheel; the bottom of the pump is difficult to access without danger of water escaping. Routing power from a wheel is typically safe in practice, but it's not impossible for a small amount of water to escape the reactor if it is temporarily overfilled. Power can also be routed out of the reactor via a gear or horizontal axle over the pump's intake tile; while this does not interfere with the pump's operation or present a danger of flooding, it makes it more difficult to shut down the reactor. In either case, it's typically wise to place a Template:L linked to a Template:L early in the power train in order to allow disconnecting the power at that point, as opposed to needing to halt the entire reactor to stop the power supply.

Expanded versions can produce more power, and can be added later with minimal advance planning; such extensibility is easily attainable by placing disengageable gears on either side of the two water wheels, then attaching minireactors at your leisure, or halting the original reactor by other means. Alternatively, it may be easier to simply produce a second reactor, then connect to the power train at another location.

Note: If created in an aquifer, there is a chance that the channeled tiles will have a natural Template:L - this will cause the pump to start the moment the first wheel is finished, flooding the work area for the second.

• This can be countered by connecting something that consumes >90 power while building the waterwheels -19 Template:L works

Mini Water Reactor

This even more compact design is quite similar to the original Dwarven Water Reactor, but can be used in tight spots that do not need more than 80 surplus power. This plan can also be considered an extension unit to the DWR, in that it can be added to one or the other side to provide an additional 80 power to the resulting power train. Safely constructing a mini reactor to add to a previously built reactor without potential flooding and/or loss of power is possible only if you first turn off the original reactor. Planning ahead is a much better option, so if you're going to need more than 170 power, build a larger reactor to start with.

As stated previously, the design below produces 80 surplus power (less additional power train).

Lower Level	Upper Level
╔ ═ ╗ █ ║ ≈ ║ █ ║ ≈ ║ █ ║ ≈ ╚ ╗ ╚ ╗ ≈ ║ █ ╚ ═ ╝	╔ ═ ═ ╗ ║ W + ║ ╝ W X ╚ + W X + + + ≈ + + + + +

Construction of the mini reactor follows the same order as for the DWR, though the channel is slightly different and only one water wheel is needed. If this is an addition to a full size reactor or set of reactors, all channels will need to be fairly full with water to start the reactor.