User:Nagidal/Sandbox

The two name-giving slits are highlighted

QuantumMenace has developed a very easy method how to dig through an aquifer of an unknown depth commonly known as the double-slit method. Its name derives from two channeled-out slits around a 2×2 staircase.

The slits are used to break into the aquifer layer below, hence their ramps are flooded (blue). During the process of securing the aquifer layer, water is being pumped from one slit to another. The screw pump can pump the water from one slit to another slightly faster than the aquifer floods it. This enables the dwarves to use the ramp of the slit to access the aquifer layer, mine one or two tiles of it and build walls which would seal off the aquifer.

General concept

Aquifers produce infinite amounts of water, but they can also absorb infinite amounts of it. This makes it possible to pump out the water from one slit to the level above the aquifer and let it fall back down and become absorbed by the same aquifer layer again.

We deconstruct half of the stairs to place a pump there. While a dwarf operates the pump, another dwarf can access the source slit via the ramp and seal off the surrounding walls of the aquifer one by one.

Pump set up at the level directly above the aquifer.

Tutorial embark setup

Even in this newbie-friendly tutorial it won't harm if you first train this on an embark which you don't intend to play after you've made it through the aquifer. Therefore I suggest you take this embark setup:

• 1 Proficient Miner
• 4 Proficient Masons
• 1 Proficient Carpenter
• 1 Proficient Woodcutter

sell the anvil to buy:

• 30+ stones (you will need 16 pieces of building material per aquifer level)
• 4 logs (to build a carpenter's workshop and the components of a pump)

Make sure you have at least:

• 1 (battle) axe
• 1 pick

to cut down trees and mine

Procedure

Preparation

Using your logs of wood, build a carpenter's workshop and craft all the parts necessary to build a pump, i.e.:

• a block
  
• an enormous corkscrew
• a pipe section

Digging through the aquifer

Dig a 2×2 staircase until you reach the aquifer layer.

Your last non-aquifer layer

Your first aquifer layer

1. Make yourself an access to the aquifer layer:

1. Channel out one tile at each side of your staircase like this.	2. This is how the aquifer level looks now.
3. Build a floor replacing the stairs between the channels.	4. Build a pump there, pumping from the west (make sure one of your dwarves has the architecture labor enabled).

2. Make sure you have at least one dwarf with the pump operating labor enabled. Start pumping the water from one side to another. And build walls around the first quadrant.

1. Designate these two tiles to be dug	2. First build the wall on the south (expect a lot of cancellation spam).
3. Then the wall on the north	4. Then these two walls (build them one by one).

3. Deconstruct the water pump, build it facing the other direction and start pumping again. Build walls around the second quadrant accordingly.

1. Start with the southern one

2. Proceed until you achieve this

4. Deconstruct the pump and the floor tiles in your non-aquifer layer and construct an up/down staircase there instead.

1. Pump and floor deconstructed

2. Stairs built

5. The procedure for building walls in the third quadrant differs slightly from what you have been building until now.

1. Dig a channel to the left and right and build a water pump between them (e.g. pumping from the east) and start pumping.	2. Don't dig under your stairs. Instead, build a wall in place of the south-eastern channel tile.
3. Continue walling off the the third quadrant by building this wall in the north.	4. Proceed building in until it looks like this. You mustn't dig the wall under the stairs. It will serve us as water sink.

6. Now for the last quadrant. We deliberately haven't dug the North-East wall under the stairs. Despite it being aquifer and leaking water, we need it to use it as a water sink now. Remember, aquifers can receive infinite amount of water, too. Deconstruct the pump and build it to pump to the opposite direction. It will spill some water on its level while pumping, but it isn't dangerous.

1. Designate these two aquifer walls to be dug.	2. Proceed with the northern wall.
3. Then bulid these other three walls.	4. Deconstruct the pump and the floors and construct Up/Down stairs there.

7. We will now deal with the last piece of aquifer.

1. Deconstruct the wall marked with the "C" to gain access to the last aquifer tile. Aquifers don't leak diagonally, so we are safe here.	2. Mine the last piece of the aquifer on this level.
3. It will produce 7 units of water wetting the ground a bit.	4. Dig downstairs to check whether there is another aquifer layer below.

When you are digging the downstairs, better have the game paused and proceed step by step (. One-Step). There is usually some water on the level where you are digging from, which would immediately run down the stairs you're digging and make the level below damp. The only way to tell whether there is an aquifer below is to stop the at the very moment when your miner reveals the first tile of it. If it is damp before the water from your level has run down on it, it is another aquifer level.

5. Construct up/down stairs on top of the downstairs to have an access to this level once the ramps are removed.

6. Deconstruct the redundant walls.

8. Level done

Enjoy your first secured aquifer layer.

If you see there is another aquifer layer below, you repeat the steps in sections 1-8. To dig through one layer of aquifer this way will take you 2 or 3 months in-game time.

Links

Quantum's original forum post