v50 Steam/Premium information for editors
  • v50 information can now be added to pages in the main namespace. v0.47 information can still be found in the DF2014 namespace. See here for more details on the new versioning policy.
  • Use this page to report any issues related to the migration.
This notice may be cached—the current version can be found here.

40d:Aquifer

From Dwarf Fortress Wiki
Jump to navigation Jump to search

An aquifer is a subterranean layer of water-bearing rock. Attempts to mine through them will result in the mined-out squares immediately filling with water, effectively halting excavation at or below their level. This, in conjunction with the fact that they are often located in areas rich in clay, loam, and sand, makes it difficult to find great quantities of stone in areas with aquifers, making for more challenging gameplay.


Dealing with Aquifers

The challenges presented by an aquifer may be circumvented in several ways. Firstly, much more of your equipment will likely be made from wood, especially early on, so it may help to be in a heavily forested area. Once you've established your fortress a bit, you will also be able to trade for stone and metals if you run short.

It is also worth noting that it is by no means impossible to find stone on these maps, it is simply much rarer. It may help to create exploratory shafts searching for pockets of stone. Be aware that mining along the level immediately above the aquifer will result in patches of 'damp stone,' which will flood if mined out; these squares will flash with water when designating mining areas.

The Ore method

On maps where the aquifer is not held in a layer of soil, but instead is held in a sedimentary layer such as sandstone, it may be possible to tunnel down through deposits of ore such as magnetite. For this to work you have to find a spot where there is coincidentally an ore deposit on each Z-level you need to dig through. This is only possible through tiresome trial and error, or through the use of a utility like reveal.exe.


The Magma method

If you have access to a supply of magma, you can create your own obsidian caissons. The water from the aquifer is not pressurized and magma is chunky, so it is safe to dig channels in aquifer. Though you will have to re-dig a lot of channels due to an element of chance, you can create a pool of magma on the aquifer z-level, and then pinch the pool off from the supply of magma with water. When it cools (which you can hasten with more water) you can dig down through the middle of a 3x3 patch of obsidian without flooding. With larger starting patches, you can dig through multiple levels of aquifer.

The Pump Method

It is possible to pump the water out of an aquifer; though the supply is apparently unlimited it can be pumped out faster than the water seeps in, allowing for a fairly safe area on the z level. This method is somewhat dangerous since problems with your pumps can lead to drowning, however, it allows a larger area to be cleared than the ice method and can be done anywhere. It's also easier to plan around a series of pumps than hoping you'll hit rock on the way down. There is an example of how to get through an aquifer with pumps here: http://mkv25.net/dfma/movie-120-aquifercmv

The Ice Method

There is a simple method of getting past an aquifer although it is restricted to a small shaft down, and not possible on all maps. You will need:

  • 9 pieces of material suitable for crafting Walls and floors.
  • 1 Carpenter or Mason (depending on your wall's building material of choice)
  • 1 Miner (using multiple miners runs the danger of one miner digging a channel on the floor another is standing on!)
  • A map which freezes

steps:

  1. Dig channels in a 5x5 square.
  2. Dig stairs on the outside of the square to allow access to the next level.
  3. Carefully dig channels underneath all the other channels and build another stair down.
  4. Continue down in this way until you're right above the water table.
  5. Dig channels around a central square.
  6. Wait for the water to freeze.
  7. The outer-most blocks of ice on the aquifer level will prevent the inner block from being damp.
  8. Dig a central set of stairs which will allow you to go through the aquifer level and access the levels below.
  9. If the map will warm up, make sure to surround the stairwell on the aquifer level with walls.
  10. This system can be expanded to allow for a bigger stairwell.

diagram:

  • C - channel
  • G - grate
  • W - wall
  • X - up/down stairs
  • > - down stair
  • < - up stair
  • I - Ice/water
  • F - Floor

Surface level:

CCCCC
CCCCC
CCCCC>
CCCCC
CCCCC

Intermidiate levels:

CCCCC
CCCCC
CCCCCX
CCCCC
CCCCC

Aquifer level + 1:

CCCCC
CCCCC
CC>CF<
CCCCC
CCCCC

Aquifer level:

IIIII
IWWWI
IWXWI
IWWWI
IIIII

Differing biomes

If your local area has more than one biome, you may be able to dig down in one biome to bridge under an aquifer in another. This won't work if the aquifer is present in all biomes, of course, but it may be useful in the case of a surprise aquifer that was not marked on the region selection screen.

Advantages of Aquifers

It's worth noting that the presence of an aquifer, while challenging, does offer some slight advantages. Firstly, much of the area underground but above the aquifer will be sand, clay, or loam, all of which can be planted in without requiring any kind of irrigation or flooding, allowing farming to get under way quicker and with less stress. Additionally, the presence of water 3-4 z-levels below ground anywhere on the map makes placing wells a simpler task, as well as ensuring easy access to subterranean water supplies.