- v50 information can now be added to pages in the main namespace. v0.47 information can still be found in the DF2014 namespace. See here for more details on the new versioning policy.
- Use this page to report any issues related to the migration.
Mineshaft stitching
 | This article was migrated from DF2014:Mineshaft stitching and may be inaccurate for the current version of DF (v50.15). See this page for more information. |
v50.15 · v0.47.05 This article is about the current version of DF.Note that some content may still need to be updated. |
When using mine shafts, dwarves will prefer to dig all of one level before moving on to the next. This can result in a lot of time spent moving, as miners go up and down mine shafts. If you have a large number of relatively-unskilled miners, this is unlikely to be a problem: digging time will dominate in any case. If you have one or two legendary miners, this is quite annoying. As a solution, you can create a single path that forces the dwarves to finish one shaft before moving on to the next. To do so, connect shafts alternately at the top and bottom layers, so the shaft snakes through the area. For example, the top, middle, and bottom layers could look like:
▒▒▒▒▒▒▒▒▒ .X▒▒X..X▒ ▒▒▒▒▒▒▒▒▒ ▒▒▒▒▒▒▒▒▒ ▒X..X▒▒X▒ ▒▒▒▒▒▒▒▒▒
▒▒▒▒▒▒▒▒▒ ▒X▒▒X▒▒X▒ ▒▒▒▒▒▒▒▒▒ ▒▒▒▒▒▒▒▒▒ ▒X▒▒X▒▒X▒ ▒▒▒▒▒▒▒▒▒
▒▒▒▒▒▒▒▒▒ ▒X▒▒X▒▒X▒ ▒.▒▒.▒▒.▒ ▒.▒▒.▒▒.▒ ▒X▒▒X▒▒X▒ ▒▒▒▒▒▒▒▒▒
Clearly you can repeat the middle layer as often as you want: I recommend at least 5-10 levels to really make this worthwhile. Note that this pattern creates a very long walkway back to the start of the mineshafts. If you do not excavate routinely, consider connecting the top-level paths of areas you have already explored.
AHK script[edit]
An AHK script to construct such a pattern is provided below, based on this script, but using many fewer keystrokes, constructing only necessary stairs at the top and bottom, and capable of being cancelled at any time.
In the previous version of DF, there was an alternate version here. It has not been tested for 2010, but there is no reason it shouldn't work.
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; stitching.ahk ;
; this is an ahk script to place exploratory mine shafts. ;
; press d and place the cursor ;
; in the top left corner of the area to be explored ;
; ;
; Alt+Shift+c to change parameters ;
; Alt+Shift+s to run ;
; Ctrl+c cancel anytime ;
; ;
; NOTE: ;
; Author: Seth Fogarty ;
; Based on a script by StrawberryBunny ;
; Bug fix from Corey Amend ;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
x = 4
y = 4
depth = 3
wait = 100
spacing = 1
DropShaft(vertdir, depth, wait)
{
if (vertdir = ">")
{
Send j
}
else
{
Send u
}
Send {Enter 2}i
tmp := depth -1
Loop %tmp%
{
Send %vertdir%{Enter 2}
Sleep %wait%
}
if (vertdir = ">")
{
Send %vertdir%u{Enter 2}
}
else
{
Send %vertdir%j{Enter 2}
}
}
$+!c::
inputbox x, Input Length, Vertical pattern length: x-axis
inputbox y, Input Width, Horizontal pattern width: y-axis
inputbox depth, Input Depth, Mineshaft depth: z-axis
inputbox spacing, Input Spacing, Spacing multiplier (1 for complete visiblity)
inputbox wait, Input Delay, Delay in miliseconds (100 recommended)
return
$^c::
Critical
ExitApp
return
$+!s::
shafts := (x * y) -1
vdir = >
i := x-1
hdir = {Down}
next = {Up}
Loop %shafts%
{
DropShaft(vdir, depth, wait)
if (vdir = ">")
{
vdir = <
}
else
{
vdir = >
}
k := spacing-1
Send d%hdir%{Enter}
Loop %k%
{
Send %hdir%{Enter}%hdir%{Enter}%hdir%
Sleep %wait%
}
Send %hdir%{Enter}%hdir%
Sleep %wait%
i--
if (i = 0)
{
if (hdir = "{Down}")
{
hdir = {Right}
next = {Up}
i=1
}
else if (hdir = "{Right}")
{
hdir = %next%
i := x-1
}
else if (hdir = "{Up}")
{
hdir = {Right}
next = {Down}
i=1
}
}
}
DropShaft(vdir, depth, wait)
if (vdir = ">")
{
Loop %depth%
{
Send <
}
}
return