- v50 information can now be added to pages in the main namespace. v0.47 information can still be found in the DF2014 namespace. See here for more details on the new versioning policy.
- Use this page to report any issues related to the migration.
Difference between revisions of "v0.34:Tile attributes"
(Importing content from v0.31 (539/614)) |
m (vs -> vs.) |
||
| Line 11: | Line 11: | ||
The entire [[Location|fortress site]] starts out as {{DFtext|Inside |6:0}}{{DFtext|Dark Subterranean|0:1}}. After that, a ray for {{DFtext|Outside|3:1}} and a ray for {{DFtext|Light |6:1}}{{DFtext|Above Ground|2:1}} falls straight down from the highest [[z-level]] for every (x,y) position on the local map, changing each tile's modifiers until something that blocks that particular "ray" is encountered. Due to this behavior, any of the previous three tile combinations will never be encountered in the same (x,y) position on a lower z-level than a higher numbered combination. | The entire [[Location|fortress site]] starts out as {{DFtext|Inside |6:0}}{{DFtext|Dark Subterranean|0:1}}. After that, a ray for {{DFtext|Outside|3:1}} and a ray for {{DFtext|Light |6:1}}{{DFtext|Above Ground|2:1}} falls straight down from the highest [[z-level]] for every (x,y) position on the local map, changing each tile's modifiers until something that blocks that particular "ray" is encountered. Due to this behavior, any of the previous three tile combinations will never be encountered in the same (x,y) position on a lower z-level than a higher numbered combination. | ||
| − | == Outside vs Inside == | + | == Outside vs. Inside == |
This attribute is determined by whether there is a roof of some kind over a tile. Weather only affects tiles which are ''Outside''. Almost any kind of geometry will block the ''Outside'' ray including natural and constructed [[wall]]s, [[floor]]s, [[stair]]s, and [[fortification]]s, and open and closed [[bridge]]s, [[grate|floor grates]], [[bars|floor bars]], and [[hatch]]es. A tile which is ''Outside'' will always be ''Light Above Ground'', but an ''Inside'' tile may be either ''Light Above Ground'' or ''Dark Subterranean''. | This attribute is determined by whether there is a roof of some kind over a tile. Weather only affects tiles which are ''Outside''. Almost any kind of geometry will block the ''Outside'' ray including natural and constructed [[wall]]s, [[floor]]s, [[stair]]s, and [[fortification]]s, and open and closed [[bridge]]s, [[grate|floor grates]], [[bars|floor bars]], and [[hatch]]es. A tile which is ''Outside'' will always be ''Light Above Ground'', but an ''Inside'' tile may be either ''Light Above Ground'' or ''Dark Subterranean''. | ||
| − | == Light vs Dark and Above Ground vs Subterranean == | + | == Light vs. Dark and Above Ground vs. Subterranean == |
Currently these two attributes are determined in exactly the same way. Once an area is exposed to the outside world, it is ''Above Ground'' and ''Light'' (and thus channeling this tile will make the tile below it also ''Above Ground'' and ''Light''). Even after being covered up again, it will remain this way. This allows growing outdoor crops inside safely. | Currently these two attributes are determined in exactly the same way. Once an area is exposed to the outside world, it is ''Above Ground'' and ''Light'' (and thus channeling this tile will make the tile below it also ''Above Ground'' and ''Light''). Even after being covered up again, it will remain this way. This allows growing outdoor crops inside safely. | ||
Revision as of 14:46, 6 May 2012
| This article is about an older version of DF. |
Every tile in Dwarf Fortress is described as Outside or Inside, Light or Dark, and Above Ground or Subterranean. These keywords can be observed from the k menu, when the cursor is located over any single tile. Currently, only the 4 following combinations are possible:
- Outside Light Above Ground
- Inside Light Above Ground
- Inside Dark Subterranean
- Inside Dark Above Ground, encountered solely in goblin curious structures.[Verify]
The entire fortress site starts out as Inside Dark Subterranean. After that, a ray for Outside and a ray for Light Above Ground falls straight down from the highest z-level for every (x,y) position on the local map, changing each tile's modifiers until something that blocks that particular "ray" is encountered. Due to this behavior, any of the previous three tile combinations will never be encountered in the same (x,y) position on a lower z-level than a higher numbered combination.
Outside vs. Inside
This attribute is determined by whether there is a roof of some kind over a tile. Weather only affects tiles which are Outside. Almost any kind of geometry will block the Outside ray including natural and constructed walls, floors, stairs, and fortifications, and open and closed bridges, floor grates, floor bars, and hatches. A tile which is Outside will always be Light Above Ground, but an Inside tile may be either Light Above Ground or Dark Subterranean.
Light vs. Dark and Above Ground vs. Subterranean
Currently these two attributes are determined in exactly the same way. Once an area is exposed to the outside world, it is Above Ground and Light (and thus channeling this tile will make the tile below it also Above Ground and Light). Even after being covered up again, it will remain this way. This allows growing outdoor crops inside safely.