Power

!!UNKNOWN!!  · xTATTEREDx  · +FINE+  · *SUPERIOR*  · ≡EXCEPTIONAL≡  · ☼MASTERWORK☼

v50.14 · v0.47.05 This article is about the current version of DF. Note that some content may still need to be updated. More Info · V

Power is used to drive devices, typically replacing or improving tasks normally done by dwarves, such as pumping water using a screw pump or milling certain types of food at a millstone. Power is produced by windmills and water wheels.

Power requirements

• Axle: (1) per tile (horizontal axles and vertical axles both)
• Gear assembly: (5)
• Millstone: (10)
• screw pump: (10)
• Roller: (2) per roller

Power transfer

Power can be transferred between devices using gear assemblies and axles. Axles transfer power in a single direction -- north, south, east, west, up, or down. Axles are classified as "horizontal" or "vertical", with the former going north/south or east/west, and with the latter going up or down Z-levels. Axles must terminate at a device, or a gear assembly, or another axle of the same kind. You cannot transfer power from a horizontal to a vertical axle (or from a north/south to an east/west horizontal axle) without a gear assembly. Horizontal axles may be built individually up to 10 tiles long; if you want a longer axle, you may simply build two or more of them in a line; you don't need gear assemblies between them. Vertical axles are always placed one tile at a time, and may be as tall as you wish.

Gear assemblies take up a single tile and transfer power to any device, axle or gear assembly within the six orthogonally adjacent tiles (north, south, east, west, above, below). Gear assemblies are best used for moving power through right-angles. For example, they can be built as bases for windmills to move power out sideways along an axle. Gear assemblies can also be linked to a lever to disengage them, which will stop power transfer through that tile. Don't do this with gears that are supporting machinery above them, as the machinery may collapse.

Because of the high power use of gear assemblies (5), axles are more appropriate and convenient to build when transferring power across horizontal or vertical distances. An axle uses (1) power for every tile of power transfer. An axle 5 tiles long will use (5) power. Axles can be directly attached to windmills, waterwheels and screw pumps in order to provide power. For security, one can make an axle-train cross a moat by first going down the moat, across, and then up. Or perhaps a screw pump will make a floor-type security-wall for a downward axle.

Devices that use power are also capable of transferring it. Adjacent screw pumps will transfer power between themselves. The only way to prevent this is to leave a tile gap between devices, or move them diagonally from each other.

Single-tile rollers transfer power in all four cardinal directions. Rollers transfer power perpendicular to their direction and may transfer along their direction (it's unreliable). Rollers need 1 rope and exactly as many mechanisms as an axle would need wood; they also may be built individually up to 10 tiles long, but have only the horizontal variant. Rollers consume 2x more power per tile than axles and need more materials. But they aren't used to connect along their direction anyway, and axles don't transfer perpendicularly on their ow. When compared to axles combined with gear assemblies, rollers are good.

Gear assembly		Roller (1x1)
1 2 3 + + + · + │ + · + + + + o + · ─ ☼ ─ · + o + + + + · + │ + · + + +	1 2 3 + + + · + │ + · + + + + + + · ─ ╟ ─ · + + + + + + · + │ + · + + +

Axles+Gears	Rollers
+ ☼ ─ ─ ─ ─ ─ ─ ─ ─ ─ ─ ☼ + + % + + + + + + + + + + % +	+ + ╟ ╟ ╟ ╟ ╟ ╟ ╟ ╟ ╟ ╟ + + + + % + + + + + + + + % + +

Axles vs. Rollers (a single U- or Z- connection):

Length	Axle+Gears Power	Axle+Gears Materials	one Roller Power	one Roller Materials
2	10	2 Mechanism	4	1 Mechanism, 1 Rope
3	11	2 Mechanism, 1 Wood	6	1 Mechanism, 1 Rope
4	12	2 Mechanism, 1 Wood	8	2 Mechanism, 1 Rope
5	13	2 Mechanism, 1 Wood	10	2 Mechanism, 1 Rope
6	14	2 Mechanism, 2 Wood	12	2 Mechanism, 1 Rope
7	15	2 Mechanism, 2 Wood	14	2 Mechanism, 1 Rope
8	16	2 Mechanism, 2 Wood	16	3 Mechanism, 1 Rope
9	17	2 Mechanism, 2 Wood	18	3 Mechanism, 1 Rope
10	18	2 Mechanism, 3 Wood	20	3 Mechanism, 1 Rope
11	19	2 Mechanism, 3 Wood
12	20	2 Mechanism, 3 Wood

Of course, a non-switching power bus (e.g. collecting power from water wheels or feeding many pumps on the same level) needs extra gears in the middle, thus rollers are far more efficient, though not trivial to connect at the ends (with water wheel arrays it's easier to alternate sides, connecting through the end wheels):

Gears	Rollers
+ + ☼ ─ ─ ☼ ─ ─ ☼ ─ ─ ☼ ─ ─ ☼ ─ + W W W W W W W W W W W W W W W + W W W W W W W W W W W W W W W + + + + + + + + + + + + + + + +	+ + ╟ ╟ ╟ ╟ ╟ ╟ ╟ ╟ ╟ ╟ + + + + + W W W W W W W W W W W W W W W + W W W W W W W W W W W W W W W + + + + + + + + + + + ╟ ╟ ╟ ╟ ╟

Axles vs. Rollers (water powerplant side bus):

Water wheel (groups)	Length	Axles+Gears Power	Axles+Gears Materials	one Roller Power	one Roller Materials
2	4	12	2 Mechanism, 1 Wood	8	2 Mechanism, 1 Rope
3	7	19	3 Mechanism, 2 Wood	14	2 Mechanism, 1 Rope
4	10	26	4 Mechanism, 3 Wood	20	3 Mechanism, 1 Rope

Frozen Components

Machine components on natural ice floors will freeze solid. This also causes all connected components to stop working. When you look at a component using 'q', you can see if the component is "frozen" (not working because it is frozen solid) or "frozen elsewhere" (not working because another component is frozen solid).

Re-activating frozen machinery is plagued with bugs - removing frozen parts frequently fails to remove the "frozen elsewhere" status of connected machinery, and removing or disconnecting machine parts that aren't frozen themselves can render still-frozen parts operative. ^Bug:2295

Seasonally frozen machinery will reliably return to working order when the ice thaws.